Skip to content

3035D

with 300E Loader

  • Standard 4wd for Maximum Traction
  • Heavy duty drive train with a gear drive transmission 8F/8R
  • On-board diagnostics including Service Advisor
  • See Ways To Save

$250/month
at 0% for 84 months with no money down.

Includes 300E Loader

Get more done with a 845 lb capacity loader. Loaders come standard with Quick Attach capabilities. Parking kits are also available to make storage a breeze.

features

Clean and simple operator's station Clean and simple operator's station

An uncluttered design gives operators of all sizes plenty of room to be comfortable. Color-coded controls are located on either side of the operator.

  • Contoured, comfortable seat enhances operator comfort.
    • Seat position adjusts fore and aft
    • Seat flips forward for protection from the elements
  • Flat operator platform provides for easy entry to/exit from the tractor.
  • Folding Roll-Gard™ rollover protective structure (ROPS) and retractable seat belt increase operator safety.

 

Operator presence system:

  • If the operator leaves the seat when the forward/reverse and range lever are in gear, the engine shuts down.
  • If the operator leaves the seat when the power take-off (PTO) is engaged, the engine shuts down.
Left-side step
Left-side step for easy entry/exit Left-side step for easy entry/exit
  • The left-side step allows for easy access on and off the tractor.
  • Foot platform has a non-skid surface for sure footing.
Seat
Seat Seat

The thick, soft padding on this seat provides a smooth and comfortable ride.

  • Seat flips forward for protection from the elements.
  • Adjustable using the fore and aft lever located under the seat, the seat slides on ramped rails to provide comfortable access to all controls.
Instrumentation
Instrument panel Instrument panel

Easy-to-read instrument panel includes the following:

  • Tachometer
  • Low oil pressure indicator light
  • Battery discharge indicator light
  • PTO engagement indicator light
  • Signal/hazard lamp indicator lights
  • Multifunction liquid crystal display (LCD) display (hours, filter cleaning information, PTO speed, etc.)
  • Filter cleaning status indicator light
Fuel tank and gauge
Rear-mounted fuel tank and gauge Rear-mounted fuel tank and gauge

All 3D Series Tractors come standard with a fuel gauge that is easy to read from the operator's station to ensure operators do not run out of fuel. The fuel tank is also located on the rear of the tractor to allow for easy refill.

Safety

Operator presence switch (OPS) in seat:

  • OPS requires the operator to be in the seat to operate the transmission or PTO.
  • ROPS is designed to meet or exceed American Society of Agricultural and Biological Engineers (ASABE) safety standards.
  • Reflective ROPS strips for better tractor visibility.
  • Seat belts are in base equipment on all John Deere compact utility tractors.
  • Key switch interlock prevents bypass starting.
  • Visual PTO warning light on the instrument panel alerts the operator when the PTO is running.
  • Turn signal and flashing warning lights operate according to ASABE standards.
  • Slow-moving vehicle (SMV) sign is provided for road transport.
Park brake
Park brake Park brake
  • Instrument panel has an indicator light for the park brake.

Two-post Roll-Gard ROPS
Roll-Gard ROPS Roll-Gard ROPS

3D Series Tractors are equipped with Roll-Gard ROPS. These folding ROPS meet the ASABE standards for compact utility tractors.

 

NOTE: The use of seat belts is recommended at all times when operating the 3D Series Tractor with the folding ROPS upright.

 

An optional canopy is available to help protect the operator from the elements.

Optional rear SCVs Optional rear SCVs

3D Series Tractors can be equipped with a field-installed rear hydraulic remote kit, providing two additional hydraulic spools on the back of the tractor. This kit can be field installed on a tractor with a loader or without a loader.

 

The functions are completely separate from the loader. These rear remotes can be hooked up to a wide variety of implements and attachments such as follows:

  • Hydraulically angled blade
  • Hydraulically controlled chute/spout on a 3-point hitch-mounted snow blower
  • Hydraulic scarifiers on a box blade
  • Many other hydraulic rear attachments

This versatile kit gives 3D Series Tractor operators the options they desire for putting their tractors into a wide range of tasks.

 

The first spool is equipped with a float position, giving the operator the ability to contour the landscape and improve the final grade with certain implements.

 

NOTE: Neither of the spools in this kit are equipped with a detent position; therefore, they should not be hooked up to anything with a motor, as the valve was not designed to be run open. The kit is designed for momentary, on-demand hydraulic flow such as moving a cylinder.

 

The approximate installation time is 1 hour to 1.5 hours.

iMatch Quick-Hitch (LVB25976) iMatch Quick-Hitch (LVB25976)

One of the greatest operator concerns involves difficulty in attaching tractor implements. John Deere has addressed this issue with the iMatch Quick-Hitch.

The iMatch Quick-Hitch provides easy hookup and a guaranteed fit for all Category 1 implements that are designed to meet the American Society of Agricultural and Biological Engineers (ASABE) Category 1 Standard S278.6 for quick-attach hitches.

  • All implements require a set of bushings for the attachment to fit and work properly with the iMatch Quick-Hitch. One set of bushings comes with the iMatch Quick-Hitch.

NOTE: The bushing set can be seen in the picture above. These bushings allow the hooks on the iMatch and the pins on the implement to fit together properly. All other implements (box blades, tillers, rear blades, etc.) will require a set of bushings to enlarge the pin to fit with the iMatch hooks. Bushings of different lengths can be found in the parts system or through a bushing supplier (see dimensions below).

  • Upper bushing
    • Inside diameter: 1.93-1.95 cm (0.76-0.77 in.)
    • Outside diameter: 3.15-3.18 cm (1.24-1.25 in.)
  • Lower bushing
    • Inside diameter: 2.24-2.26 cm (0.88 to 0.89 in.)
    • Outside diameter: 3.63-3.66 cm (1.43 to 1.44 in.)

Regular service and maintenance are essential to the performance, productivity, and longevity of the tractor.

  • Easy access to most regular service points minimizes service time.

  • Tractors are equipped with extensive onboard self-diagnostic capabilities and are fully compatible with the John Deere-exclusive Service ADVISOR™ system.

  • Hydraulic oil service interval increased to 1200 hours when using Hy-Gard™ products. Hydraulic oil filter will need to be changed every 400 hours.

  • Fuel tank is located on the rear of the tractor to allow for easy access when fueling.

Fuel tank on rear of the tractor Fuel tank on rear of the tractor
  • Four quarter turn fasteners allow operators to easily remove the engine side panels to access the engine compartment
Easy access to engine compartment Easy access to engine compartment
  • Daily service requirements are minimal and simple to accomplish. Most service interval requirements can be performed with a basic understanding of procedures and common tools.

 

Daily service is quick and easy Daily service is quick and easy

All items in the daily service schedule can be performed without the use of tools:

  • Engine oil, hydraulic oil, coolant level, and the water separator can be conveniently accessed.

  • The engine can be easily accessed by simply raising the hood for more periodic maintenance checks.

NOTE: Always refer to the operator’s manual for complete maintenance and service recommendations.

specs

Engine power (gross)25.5 kW
34.7 hp
Power take-off (PTO) power23 kW
30.8 hp
Steering hydraulics16.8 L/min
4.4 gpm
Implement hydraulics22.4 L/min
5.9 gpm
Hitch typeCategory 1
Lift capacity, 24-in. behind link arms757.4 kg
1670 lb
Standard transmission; forward/reverse8F/8R synchromesh shuttle shift gear transmission
Cruise controlNo
Approximate shipping weight (open-station; cab)1275 kg
2811 lb
Wheelbase157.4 cm
62 in.
ManufacturerYanmar
Engine model3TNV88C-KJPT
Engine power (gross)25.5 kW
34.7 hp
Power take-off (PTO) power23 kW
30.8 hp
Rated engine speed2400 rpm
Injection pump typeHigh pressure common rail direct injection
AspirationNatural
Emissions complianceFinal Tier 4
Cylinders/displacement3 / 1.64 L
3 / 100.2 cu in.
Number of cylindersThree
Cylinder linersCast-in-block
Bore and stroke88 x 90 mm
3.46 x 3.54 in.
Compression ratio19.1:1
LubricationPressurized
Cooling systemWater pump
Air cleanerDual element
Engine torque at rated speed87 Nm
64.2 lb-ft
Fuel tank capacity36.7 L
9.7 U.S. gal.
Battery size600 CCA
Alternator (12-V)55 amp
Starter size1.4 kW
1.9 hp
TypeHigh pressure common rail direct injection
Fuel consumption
Standard transmission; forward/reverse8F/8R synchromesh shuttle shift gear transmission
Left-hand reverserYes
Transmission gear ranges4 gears and 2 ranges
Final driveSpur Gear
BrakesWet disc
SteeringPower steering
Axle capacityFront
880 kg
1940 lb
Rear
1600 kg
3527 lb
CreeperNo
Cruise controlNo
Differential lockYes
TypeOpen center
Pump rated outputSteering
16.8 L/min
4.4 gpm
Implement
22.4 L/min
5.9 gpm
39.2 L/min
10.3 gpm
Pump typeSingle gear
Maximum operating pressure172.4 bar
2500 psi
Draft control sensingPosition control
Remote control valves availableUp to two (optional)
TypeCategory 1
Lift capacity, 24-in. behind link arms757.4 kg
1670 lb
Standard540 rpm at 2400 rpm
ControlMechanical
ClutchTransmission
Brake (for mid and rear PTO)Wet disc
Crankcase with filter4.5 L
4.8 qt
Transmission and hydraulic system33 L
34.8 qt
TypeBull Gear
Rollover protective structureType
Foldable
ASABE S478
Platform - flat/straddleSemi-flat
Gear shift location - console/floorRight-hand side
Wheelbase157.4 cm
62 in.
Front axle clearance35 cm
14 in.
Turning radius with brakes1.63 m
5.3 ft
Approximate shipping weight (open-station; cab)1275 kg
2811 lb
FrontFarm - 7-14
Turf - 27x8.5-15
R4 - 25x8.5-14
RearFarm - 11.2-24
Turf - 41x14-20
R4 - 15-19.5
ToolboxYes
Tilt steering wheelNo
12-V OutletNo

Reviews

4.0
(2 reviews)
Recommended by 100.0%
Write a review
5 star
1
4 star
0
3 star
1
2 star
0
1 star
0
Value4.5
Quality4.0
Ease of Use4.5

Offer ends October 30, 2020. Offer valid while supplies last. Prices and availability may vary by dealer. Taxes not included. Images for illustration purposes only. Subject to approved credit by John Deere Financial. Down payment may be required to receive financing. Taxes, freight, set up and delivery charges could increase the monthly payment. Restrictions may apply outside of Hutson’s area of responsibility. See dealer for details.

Our sales staff cares about finding the best unit for your needs

×

Get A Quote

What would you like included in this quote?

What type of quote would you like?*

*You may qualify for additional discounts. If you choose 'Custom', we'll ask some qualifying questions to ensure you get the best deal possible.